Відео

You lost me at 300 bucks. And then sent me out the door with just drop the old one, pliers and all, into the pan. Lol

i got a Motorhome 34' it has the Triton V10 Ford motor in it . Its a year 2000 and I love it runs like a top. gas mileage sux Yup . i tow a car behind it and it get about 8 to 8.5 mph a great motor

Love my 04

well done nice john

I lost the dipstick on my dad's 7.3Lidi. The one the ford place gave me wasn't correct, tho they insisted. I ended up buying one from a wrecking yard. The one from the ford dealer was for a 7.3L idi turbo. It was different.

But I make over 150K because I have my degree. It's hard work. But ya should all get a trade or degree. No matter what. Invest in yourselves.

Smoke doesn’t mean you got more horsepower

And it only took 6 minutes to even mention a tie rod end🙄🙄

I'm thinking of picking one of these up with 350K miles on it. What are your thoughts? They say AC runs good and it runs fine now.

97 f250 hd. Almost rust free and running strong. Also no def or epa bs.

Your 7.3 runs out of oil it will shut down!!! Serious!! The minute you have no oil pressure she is not running

This guy ruined my whole day

They still haven't hired lol

Why do folks insist on calling bearing cups races? A race is the ring that's pressed on or held on to the axle with a set screw to hold a bearing to an axle. These are BEARING CUPS!

If it’s legit from Cali it should have the prop 65 cancer BS warning! 😂🤣

Why would you drop the fuel tank and check the fuel strainers?Just back, feed it with a 150 ps.I.Air if it's plugged up it'll drop down to the bottom of the tank and forget about it

I have had to replace the whole assembly more than once in my day because of this. Awesome.

~~Tightening is a correct step. Before you do anything though, after you let the penetrater soak. Take a metal rod/shaft, preferably the size of the bolt head, w/good size hammer&give each one a couple good healthy wacks. Not only will you find you may not the torch? But possibly break loose after tightening it the first time? ~~I worked at Hydraulic shop 15 year,that did the trick w/ 5/8" bolts&up. Not once did we ever have to use the torch unless the gland&or piston was seized.

anyone noticed blood on the passenger seat?

Lol ASE means you know the basics in each area tested. I have all 8, expiring end of month. I will not renew them.

I found a receipt in the past on garagejournal with atf and methylated spirit. Thank you for remembering me. I personally mix mine with dampening oil of old struts and methylated spirit.

Lies

So my 7.3 runs and then dies and starts back up and I got oil on mine so do you think that is what it is

freight shaker MUCH

12:00, The WIX filter has better paper, true... BUT there is also LESS FILTER PAPER MATERIAL IN THE FLAM. One Other FILTER Comparison cut the paper Out and MEASURED THE LENGTH OF IT. 19:00, OH it is you great to see the differences.

I always liked your ideas on chucky's channel...

I bought an 02 Excursion 6.8 V10 back in 2018. Hands down best vehicle I’ve ever owned. 213,000 on the clock and have done brakes, battery, steering gear box, plugs and some preventative maintenance. It’s tough on gas when towing but it’s a work horse and a daily driver. If anyone has experienced this I’d appreciate some thoughts. I’ve been getting a fast ticking noise coming from where I believe is the front of the engine. I’ve done lots of research and there are so many different opinions from…..it’s normal don’t worry about it to injectors, spark plugs or possible timing components ! Any thoughts ?

This makes me not afraid to do a big job for this type of equipment. Thank you!

After it starts crack the top cap and let the level go down, then tighten it back up so owner doesn't accuse one of not changing the filter. It's clearly shown in the instructions.

I got a 2008 f250 v10 and I slung a rod on mine at 246k miles 😂😂 what u mean that ain’t a problem

So i have the cat 3024c and i cant seem to get it to idle up. It was at high idle then it just went to low 1500 rpms. Anyone have a solution.

I change oil about 5000miles and filter. But have to add a small amount during changes. Milage is not too good on the rv use. Had missfire and changed two coils on cylinder 1 and 9 with Blue Streak. Now it runs so smooth again. A wonderful engine. Only noisy on ''towing'' downhill and uphill between 4000-5000 rpm.

What happened to Chucke, he disappeared and I can’t find his videos any more

To boring

Great video Thanks a million for the info.., I’m trying to determine if the 7.3 Is hydro locked as it seems to be locked up big time. So I’m going to pull the GP to see if the there is oil on top of the pistons. Also might re-place the o’rings in the injectors

Looking for info on how to set the load and idle needles on the carb (DLTX 67). I believe you turn in the valve all the way and then turn it out a turn and a half, not certain.

Excellent video dude! Bought my 99 ps new, u & Ron are helping keep her on the rd

4:33 understandable, however why not just orient the block to where the manifold is on top of it, so that when you loosen the bolts, there's no weight from the manifold pulling down on them?... Easier said than done if you haven't got fancy equipment, but most garages who do restorations like that on old junkers have something that could perform such a function.

I’ve been filling my toolbox with all the cheap imports…why pay double at Harbor Freight or 200X through snap on? I buy every type of puller, spark plug insert boring kit, vacuum gauge, AC manifold, vacuum pump and anything else that I can use to make my life easier. Say what you want about cheap imports but I’ll take them versus not having the tools I need.

Hello. I bought a Motor Home with an 8.9 Cummins with only 5000 miles on it. Does not want to fire up. I changed filters but nothing. We made sure we were getting fuel to lines but got to pressure valve and no fuel after pressure valve. What do you think it could be. I’m going to run codes and see what it says.

You’re actually setting the gap on those. Yours should be .276”. I have the same unit. Specs and instructions are available in the operators manual. Free on the JD website.

All new battery chargers are "smart chargers". BUT all chargers are made in China or Korea. My neighbor has a John Deere battery charger and it still works after 30 years

Looked like it woulda been good enough to seal it up right. Plus you probably voided jaspers warranty for this customer by messing with their “reman” block.

Great video. Title is all wrong! How do i find this video when i finally need it?

They roll over at 400k that truck could have almost 800k and you'd never know lol

what a crappy video

4 gallons a 7.3 holds

I’m going with the silicone

So how has that chrger held up aftr few years ? Got same one BUT for home use seems fine no issues

lol